1、 Application scope and working mode of filter element ultrasonic cleaning machine

濾芯超聲波清洗機是適合于各種化工行業、金屬拉絲機、化纖行業、凈水設備等行業，主要清洗被臟塵、粉末、膠劑、碎屑等堵塞的內孔盲孔等。這些部位人手很難接觸到，通過超聲波清洗機能對深孔、細縫和隱蔽處清洗干凈。

The filter element ultrasonic cleaning machine is suitable for various chemical industries, metal wire drawing machines, chemical fiber industries, water purification equipment and other industries. It mainly cleans the inner hole and blind hole blocked by dirty dust, powder, glue, debris and so on. These parts are difficult to reach by hand. Deep holes, fine seams and concealed places are cleaned by ultrasonic cleaning machine.

濾芯超聲波清洗機廣泛應用于：機械行業、表面處理行業、儀器儀表行業、電子行業、醫療行業、半導體行業、鐘表首飾行業、化學生物行業、光學行業、紡織印染行業、石油化工行業、玉石飾物加工行業、眼鏡行業等。利用機械轉動臂將濾芯在超聲波清洗機中勻速轉動，超聲波對濾芯表面及細孔進行不間斷轟擊，清洗速度快，清洗效果好，清潔度高，達到所有被堵塞細孔內臟物全部洗清的效果。

Filter element ultrasonic cleaning machine is widely used in: machinery industry, surface treatment industry, instrument industry, electronics industry, medical industry, semiconductor industry, watch and jewelry industry, chemical and biological industry, optical industry, textile printing and dyeing industry, petrochemical industry, jade jewelry processing industry, glasses industry, etc. The mechanical rotating arm is used to rotate the filter element at a uniform speed in the ultrasonic cleaning machine, and the ultrasonic bombards the surface of the filter element and fine holes continuously. The cleaning speed is fast, the cleaning effect is good, and the cleanliness is high, so as to achieve the effect of cleaning all internal organs of blocked fine holes.

二、超聲波清洗機使用注意事項

2、 Precautions for use of ultrasonic cleaning machine

超聲波清洗機在使用的過程中一定要注意使用規則，濾芯超聲波清洗機在使用的過程中一定要切記注意事項。濾芯超聲波清洗機電源及電熱器電源建議有良好接地裝置。這對機器能否正常的運轉十分重要。另外，電源電壓變化超出機器允許范圍時，應立即暫停使用，避免出現用電問題，或者因為電路問題對機器產生損害。

Pay attention to the use rules during the use of the ultrasonic cleaning machine, and remember the precautions during the use of the filter element ultrasonic cleaning machine. The power supply of filter element ultrasonic cleaning machine and electric heater must be well grounded. This is very important for the normal operation of the machine. In addition, when the power supply voltage changes beyond the allowable range of the machine, the use shall be suspended immediately to avoid power problems or damage to the machine due to circuit problems.

如有物體跌落超聲波清洗槽內，應及時取出，否則會磨損缸底。切記被清洗物體不應直接放在槽底(超聲輻射面)清洗。

If any object falls into the ultrasonic cleaning tank, take it out in time, otherwise it will wear the cylinder bottom. Remember that the object to be cleaned should not be directly placed at the bottom of the tank (ultrasonic radiation surface) for cleaning.

超聲波清洗機不應頻繁開、關超聲(間隔應在1分鐘以上)，以免功率器件浪涌電流過大損壞。開啟超聲開關時應注意發生器散熱風扇是否運轉正常，否則易因過熱損壞器件。超聲波清洗機清洗缸缸底應定期沖洗，不宜有過多的雜物或污垢。

The ultrasonic cleaning machine shall not be turned on and off frequently (the interval shall be more than 1 minute) to avoid excessive surge current damage to power devices. When opening the ultrasonic switch, pay attention to whether the cooling fan of the generator operates normally, otherwise it is easy to damage the device due to overheating. The bottom of the cleaning cylinder of the ultrasonic cleaning machine shall be washed regularly, and there shall not be too many sundries or dirt.